Yardpump
Here is a list of materials and parts for the Yardpump divided into what we sell you and what you buy locally. You need to measure your depth (S) from the top of the casing to lowest water (in fall), and depth (B) to the bottom of the well. Your well yield (Y) is on the welldrilling report usually filed with the state or provincial government groundwater branch. Then the safe but economical depth V to set the pump down the well casing is given by V=S+(B-S)*18/(Y in litres per minute). We do not supply the wire needed because lengths are different for each installation. This 3/16" vinyl cover of 3/32" galvanised wire of 7 strands of 7 wires each is sold as clothesline wire eg Steelplast Durable 135 or Extra 120, or steering cable for small outboard motors.
We supply	You supply (Typical retail $70 USD @V=40')
1 - YP Instruction manual 1 - YC Patent pump shuttle 1 - YC Cylinder bushing 1 - YP Vinyl wire seal in ½" MPT pipe plug 1 - YC Spare static seal Sorry we are no longer able to take orders but are seeking developing country manufacturers for these units Few tools required such as 1.9" (1½" pipe size) holesaw for aluminum. No welding is necessary.	1 - 1¼" MPT slit filter ( only if well is very dirty) 1 - 1¼" FIPT x S PVC transition Pipe sealant Exterior Construction adhesive 4 - # 24 Stainless steel hose clamps 6 feet - 1¼" Schedule 40 PVC pipe for cylinder 3 feet- 1/2" nominal type K rigid copper or brass tubing V feet - 1½" Polyetheylene utility riser pipe V+10 feet - 3/16" vinyl coated 3/32" galvanised wire Well seal cap steel or plywood with hole for 1½" pipe 1 - 1½" PVC slip T 1 - 1½" Sx ½ FIPT bushing 1 - Wide groove ballbearing 6" clothesline pulley 1 - Treadle board 36"x10" ¾" plywood 2 - 1/8 wire cable clips N248-278 1 - U Bolt N222-083 1 - ¾" sch 40 galvanized pipe x 10" long 1 - 7"x 9" x 1/8" aluminum plate 1 - 1.25 square HSS steel tubing x 48" long 1 - 1"x 2" x 1/8" wall rectangular HSS tubing x 3" 1 - 3/8" x 36" redirod 2 - 5/16"diameter x 2½" long bolts 2 - ½" diameter x 1" long bolts 2 - ¼"diameter x 1½" long bolts V = top of well casing to max pumping drawdown
Cottagepump
Here is a list of materials and parts (see schematic) for the Cottagepump divided into what we sell you and what you buy locally. You need to measure the inner diameter (ID) and outer diameter (OD) of your wellcasing, your depth (T) from your frost-free level in the ground to lowest water level (in autumn), and depth (M) from frost-free to the bottom of the well. Your well yield (Y). This is on the welldrilling report usually filed with the state or provincial government groundwater branch. Then the safe but economical depth (E) to set the cylinder below your local frost-free depth is given by E = T + (M-T) x 18 / (Y litres/minute). You must also measure your horizontal pipe run distance (H) from the wellhead to the kitchen. We do not supply rope because rope lengths are different for each installation and they should be measured and cut onsite. Your rope must be low-stretch and resist abrasion. The low-cost long-length option is to use 3/16" vinyl covered 3/32" clothesline of 7 strands of 7 wires each for the straight runs and splice in ¼" 3-strand polyester (eg. Marlow pre-stretched) rope to run over the pulleys. Suitable clotheslines are Dura 135 and Extra 120 by Steelplast, also used for outboard steering cables. The less-labour option for short H & V of about 100' is to use low stretch 4mm Supercord, or 5mm Mistraline for medium H and V of about 150'. Phone 800-643-6350 or Fax -6340 to order these from G&B Ropes (Orillia, Ontario).
We supply	You supply
1 - CP Instruction manual 1 - YC pump shuttle 1 - YC Cylinder bushing 1 - CP Pitless adapter specify D's of your casing 1 - CP Wellhead pulley in DURA T 1 - CP 1½" cottage GENOVA elbow with pulley 2 - Quick-lock screws for breakable pipe joints 1 - Spare static seal Sorry we are unable to offer CP kits anymore. Remember to specify your ID and OD. N designates National Mfg. part #	1 - 1¼" MPT slit filter ( only if well is very dirty) 1 - 1¼" FIPT x S PVC transition Pipe sealant PVC cement Exterior Construction adhesive 4 - # 24 Stainless steel hose clamps 6 feet - 1¼" Schedule 40 PVC pipe for cylinder 3 ft 1/2" nominal type K rigid copper or brass tubing E feet - 1½" Polyetheylene utility riser pipe H feet - ¾" Bury horizontal (preferably SDR 26) PVC 1 - ¾" FIPT x S bushing 12 feet - 1½" PVC SDR 26 pipe (2, 3, 7-foot lengths) 1 - 1½" S end cap 1 - ¾" S x 1½ S bushing 3` of 4" PVC pipe for access to elbow 1 - 1½" PVC Slip T 1 - Hardware bent steel strap N226-338 1 - 6.5" ball bearing (clothesline) pulley 1 - Screw eye 2" into ceiling joist N220-889 2 - Rope eye (1 stainless steel, other N176-818) 1 - U bolt N222-083 1 - 4'x1' 1-inch (stair tread) plywood for treadle 2 - 2" Door hinges N139-832 E+H+20 feet - ¼" Clothesline wire/low stretch rope (see above) E = Bury depth to max pumping drawdown H = Horizontal distance from well to sink
Tools Required for Installing the Cottagepump (not included) 3/16" drill ¼" 20 NC tap 3/16" round file Cutting torch or ¾" (1.05") Pipe holesaw for metal 14" pipe wrench for metal plumbing Strap or chain wrench (for plastic pipe) 5/16" socket for hose clamps Shovel (for digging trench) Drill (for mounting screw eye in ceiling joist) and U bolt in treadle) Screwdriver (to mount hinges on treadle boards)
ReCycle Trailer for Cargo
Prototypes of the ReCycle Bicycle Trailer are for sale locally on Vancouver Island from $125 CAD.